How to revive your old yard tools
Restoring Yard Tools
Extend the Life of Your Tools
Do Your Own Mower Maintenance and Save
9 8 Great Ways to Save Money on Lawn Care
How to Buy Hand Tools
Can They Be Saved?
As first time home owners, my husband and I did not own any yard equipment. A family friend donated several basics (yard rake, hoe, shovel) but the handles of nearly all these implements are old and rough, making them hard on the hands. Additionally, the metal parts are pretty rusty. Do you have any tips for restoring yard tools?
Wrapping the Handles
I would suggest buying some tape used to rewrap tennis rackets and wrap the handles. As for the rust, try spraying with WD40 then scrub with steel wool.
Good Enough for the Marines
The shovels and axes we use for field operations in the Marine Corps get a beating! These tools often come back from the deserts of Twenty-Nine Palms or the cold, wet climate of Norway in real bad condition.
We sand down the wooden handles with light grade sandpaper and then apply linseed oil liberally to the wooden handle. For metal parts, first sand them down, preferably with a wire brush grinder and then spray paint using cheap paint found just about anywhere.
Staff Sergeant S.B., USMC
A Little Elbow Grease Required
Handles, if not cracked, can be made serviceable by sanding smooth with some rough (say, 50 grit) sandpaper. Then oil with linseed oil.
Rusty tools should have the rust taken off with a wire brush, followed by a couple of applications of naval jelly. For the tools that are supposed to have edges (shovel, hoe), put the edge back on with a file. The rake doesn't need the file. If the handles are still too irritating for you then you may need to wear gloves.
Tool Care Makes a Difference
What I did with the rough handles on my garden tools was sand them and apply polyurethane. My mom used to just paint them with an ordinary exterior paint and a special hint was to paint the top end of the handle a bright color so the hoe, rake, etc can be seen quickly if you drop it into the weeds or grass.
Now about the metal part, my hubby used to soak them in muriatic acid. Then he would take it out and rinse it. Then he sprayed it with WD40 and sharpened the edge. After that he would take a soft cloth and rub oil into the metal. I have not done this to my hoe or shovel since he died and I sure notice a difference.
Suggestions to Help with the Tools
There are a few different ways to solve the rough handle problem. Unfortunately not so many for the rusty "work end" of the tool.
- The cheapest, easiest way to "fix" the rough handle -- go to the dollar store and get a pair or work gloves for $1.00.
- Plastic duct tape (with the fibers, not the metal kind) can be wrapped around the upper portion of the tool, where your hands would be (this can get slippery though!)
- Sand the handle with a "fine" sand paper to remove "splinters."
- The hardware store sells foam insulation to wrap and insulate water pipes (it looks like a foam rubber water hose). Purchase a length of this (about 12 inches for each tool), of the appropriate diameter to fit around the handle of the tool. Slit the foam it's length, if it is not already split. Wrap tightly around the tool, and tape in place with plastic (not metal) duct tape, at the top and bottom and very center of the foam strip. If you tape the whole piece of foam, it won't be able to "breathe" and will be very slippery if your hands sweat.
Larger hardware stores sell a "liquid rubber" used to coat hand tools. This is pretty expensive stuff to buy (its usually sold in pints), for the amount you would need.
Now, as far as the "working end" of the tool, it will take some work on your part to "recondition" the used tool. You will need to clean the old rust off the tool. Use a piece of coarse, dry steel wool, applying vigorously with lots of "elbow grease."
After you have removed all loose rust and are down to the metal, if you wish to use a finer dry steel wool, you may make the tool look even newer. When you have the rust removed and the tool is cleaned to your satisfaction, use a rag to clean the tool with rubbing alcohol, to remove all "rust dust" and any other debris. Allow enough time for the alcohol to completely evaporate.
for tools and supplies for your home improvement project Shop at AceHardware.com
The final step is to help protect your newly cleaned and restored tool. To do this, apply a very thin coating of paste wax with a rag and then wipe off any extra wax. This is especially good for shoveling implements. It will help what ever you are shoveling slide off more easily. If you are doing a raking implement, you don't have to do this step, but it wouldn't hurt! Hanging your tools inside a closet, shed or garage will help keep them in better condition. Good luck restoring your yard tools!
Take the Next Step
- Learn how to extend the life of your lawn and gardening tools.
- Once those yard tools are restored, take a look to see if you are saving all that you can on your lawn and landscaping and in your garden.
- Could spending 5 minutes reading a newsletter twice a week save you time and money every day? Dollar Stretcher Tips readers think so. Subscribe and find out how many ideas stretch your day and your dollar!
- Visit our Pinterest board for A Frugal Lawn and Garden.
Also in Home
- 6 cheap, effective home security solutions
- 5 simple and affordable luxuries for your home
- 5 frugal ways to expand your living space
- Top 10 DIY mistakes made by home 'handymen'
- Tha basics of financing a home improvement project
- 4 secrets to budgeting for a home purchase
- Homemade fireplace logs
- Ways to reupholster a couch inexpensively
- Frugal ways to winterize your home
- Homemade fabric fresheners
- Surviving the water bill
- Find the best mortgage rates in your area
- 3 ways to use a mortgage calculator
- Mortgage calculator: Calculate your payment and more
- Home equity calculator: HELOC vs. line of credit
- Should I borrow from my home equity?
- How much can additional payments save me on my mortgage?
- Who offers the most home insurance discounts?