Repairing a Wooden Deck
Refinishing a Pressure-Treated Deck
Building a Recycled Deck
The old floor on my outside wooden deck is in very bad shape. I am unsure whether to refinish it (which would require stripping and also replacing quite a few rotten boards) or replace the entire decktop. It is currently made from 2" thick by 6" wide Douglas fir planks. I like the look of cedar, but the lumberyard suggested I consider pressure-treated wood and a product called TREX, which is a synthetic wood, as alternatives. Apparently there are a lot of choices out there. Do you have any comments concerning the different options?
Cedar is a fine natural decking product and many people prefer it for aesthetic reasons. Cedar, like the other naturals decking material redwood, does not shrink appreciably or warp. It has a long life and a natural resistance to insects and fungus. However, this resistance is not permanent and the actions of the sun and weather will eventually take a toll on the exposed surfaces. Therefore cedar decking should have an annual application of a clear sealer for maximum life. Of course, it can also be stained or painted.
If you would prefer a tougher decking with a longer life than cedar, two options are pressure treated yellow pine or one of the synthetic decking products such as TREX or plastic lumber. Pressure treated wood decking can be purchased in two thicknesses… nominal 2" thickness (actual 1 1/2") or 5/4" thickness. Pressure treated (PT) wood will not rot BUT should be sealed annually to protect it from the weather and the sun. Over time, unprotected PT wood tends to crack and splinter without this added protection. Since PT wood can shrink and twist as the preservative evaporates… fresh PT wood is installed while still somewhat "wet" with preservative… it is not uncommon that a few deck boards may need to be replaced within a few years of installation. This twisting can actually pull nails and split boards! To minimize these problems PT wood should be sealed immediately after installation with a special PT wood sealer. This slows down the evaporation and thus minimizes shrinkage.
If you plan of using a stain or paint, it is wise to give the surface at least six months after the initial sealing for proper adhesion.
TREX boards, available in 5/4" and 2" thickness', are composite products made from 50% recycled plastics and 50% real wood fibers. This combination makes TREX somewhat more stable than plastic lumber (at a given thickness) and more durable than any 100% wood product since it is virtually impervious to moisture. TREX is not rigid enough to be used as a structural support… it is strictly for decking purposes. TREX does not require any preservative or treatment and weathers to a gray tone. Though not necessary, it can be painted or stained if desired… but this will add to your maintenance chores! TREX is available at most lumberyards and some home stores.
Plastic lumber is made from 100% recycled plastic and is available 1" and 2" thickness' for decking, and is also available in a 1" tongue-and-groove style. Plastic lumber is not only available as decking… an entire deck can be built from plastic lumber components! Plastic lumber is totally impervious to moisture so no sealing is necessary. It is available in a wide range of colors, which is good because it does not hold paint or stain well. Finally, since there is no toxic component as with PT wood, it can also be used indoors in showers, damp basements, etc. One downside is that this product is less widely available than TREX or the other wood products.
One critical issue in choosing a retrofitted decking material is the "center-to-center" (c-t-c) distance between the supporting floor members, or joists, of your existing deck. Every decking material has a maximum c-t-c distance for adequate strength without excessive flexing. Cedar, PT wood and TREX in 5/4" thickness have a c-t-c maximum of 16. 2" thick TREX and PT wood can be installed with a maximum c-t-c of 20". Plastic lumber of one inch thickness requires a maximum of 12" c-t-c because it is not as rigid as PT wood or TREX. However plastic decking is available in 2" thickness that can be used on 16" centers. Keep in mind that if your decking is diagonal, you may need more reinforcement under the decking since the actual center to center may be 20" or more.
Another critical difference between these products is in the installation. Though all products can be installed using screws or nails, there are differences in each product's reaction to temperature changes. Cedar does not shrink or expand significantly so board spacing during installation remains constant. Pressure treated wood tends to shrink as the moisture from its chemical treatment evaporates, so most installers leave no gaps between the boards… shrinkage will take care of that! Both TREX and plastic lumber will expand and contract with temperature changes, so allowances have to be made in positioning the boards to allow for these changes… or else the decking may buckle! The temperature during installation is also important… installation at low temperatures requires more initial spacing than installation at high temperatures.
All the decking products mentioned can be installed with decking nails or screws, though the high-tech pullout-resistant nails used for PT lumber are unnecessary for the other products
copyright 2000 G.G. Alonzy
Have a small home repair question for THE NATURAL HANDYMAN? Just click here www.naturalhandyman.com/aitikia
For more home repair information, visit NH's growing list of original home repair articles and quality links www.naturalhandyman.com
If this information has been valuable to you, please consider making a small donation to support NH's free service to the home repair community! For more information, please visit our "Friends" page www.naturalhandyman.com/friends
The Natural Handyman Site Directory
- Home Repair Articles www.naturalhandyman.com/iip
- Home Repair Links Library www.naturalhandyman.com/linkslibrary
- NH's Bookshop www.naturalhandyman.com/bookshop
- Find a handyman at www.naturalhandyman.com/network
- Win unique home repair gifts and prizes at www.naturalhandyman.com/contest
Please read the important copyright and disclaimer information is located at www.naturalhandyman.com/copyright
Also In This Week's Issue
- 5 ways your house can make you go broke
- How to regain storage space and cut the clutter
- 5 simple and affordable luxuries for your home
- 12 ways to lower heating bills
- Free fireplace logs
- 8 kitchen remodeling projects for under $500
- 6 cheap, effective home security solutions
- 6 hazards your home insurance won't cover
- How to save on mortgage as rates rise
In The Dollar Stretcher Community
Get free money-saving articles in your inbox each week!
Sign up for our free weekly newsletter Surviving Tough Times.