Shower Grab Bars
First Aid for the Bathroom
Cheap Bathroom Fix-Ups
I plan to install safety grab bars in a couple locations. There is ceramic wall tile around the tub/shower. Can I drill holes thru the tile to anchor the bar securely? If so, is a special drill bit required so the tile won't break or shatter? Any other tips for drilling through tile? In another area is drywall. If I can't align with a stud, will toggle bolts be adequate ?
HC from Tampa, FL
Ideally you would want to install the grab bars onto wood studs, whether there is tile or not. However, most grab bars are not sized to precisely span the standard 16" center-to-center spacing of wall studs. Some installers will purchase longer bars... 18" or 24"... and install them at an angle so that each end aligns with a stud. However, all homeowners do not want this "askew" installation.
Using toggle bolts (the folding fasteners commonly used on drywall) is an acceptable solution for one or both ends as long as you use 3/16" or (ideally) 1/4" toggles. You do not need to use toggles in every hole... two 3/16" toggles per side is adequate for most installations. If you can locate the studs (sometimes difficult through ceramic tile, even with a "stud finder"), try to attach at least one end of the grab bar to a stud.
Ceramic tile can be drilled with either sharp masonry bits or with special ceramic tile bits. I emphasize sharp! Buy a new one for this job! To help start the hole where you want it, put a piece of masking tape on the tile to keep the business end of the drill bit from slipping until it makes a dimple in the tile. Fortunately, the location of the hole is not micrometer critical, since it will be covered by the grab bar mount.
I like to drill the smallest hole possible, so I use a unique toggle bolt called the "Toggler." It is a specially designed toggle that uses a solid bar instead of a folding toggle and is held in place on the wall with a vinyl harness. The advantages of the Toggler are two-fold. First, you do not need to drill as large a hole to get the same strength... important when drilling through ceramic tile. Second, the toggle bar stays in place when installed. This means that, unlike a standard hinged toggle that drops into the wall when you remove the bolt, the Toggler's bolt can be unscrewed and rescrewed numerous times.
You can get more information on the Toggler at www.mechanicalplastics.com/. You can probably buy them locally but you may have to do a little hunting.
As a final note, with standard toggles, part of the hole in the wall may appear around the edge of the grab bar if the holes in the grab bar are close to the edge. To prevent this, offset the hole for the toggle towards the center of the grab bar mount. Just make sure that the desired location of the bolt is within the offset hole. Have fun!
copyright 2001 G.G. Alonzy
Have a small home repair question for THE NATURAL HANDYMAN? Just click here www.naturalhandyman.com/aitikia
For more home repair information, visit NH's growing list of original home repair articles and quality links www.naturalhandyman.com
If this information has been valuable to you, please consider making a small donation to support NH's free service to the home repair community! For more information, please visit our "Friends" page www.naturalhandyman.com/friends
The Natural Handyman Site Directory
- Home Repair Articles www.naturalhandyman.com/iip
- Home Repair Links Library www.naturalhandyman.com/linkslibrary
- NH's Bookshop www.naturalhandyman.com/bookshop
- Find a handyman at www.naturalhandyman.com/network
- Win unique home repair gifts and prizes at www.naturalhandyman.com/contest
Please read the important copyright and disclaimer information is located at www.naturalhandyman.com/copyright
Also in Home
- 5 ways your house can make you go broke
- 5 simple and affordable luxuries for your home
- 12 ways to lower heating bills
- Will my insurance spike if I rent out my basement?
- Why pay extra toward mortgage principal?
- 5 tips to sell a home before buying another
- 6 ways to stock your "man cave" for under $500
- 6 home projects that don't pay for themselves
- Should I refinance my home equity line?