© 1999 G.G. ALONZY
I have 4 mirrors, each with 2 sections 16" wide by 84" tall, mounted on 1" particle board and held together by an 84" strap hinge. How & what do I use to mount them against the wall without them falling down. They are very heavy! Or is it better to separate them by removing them from the hinges.
NM from Suffern, New York
It is always easier to hang something that is lighter, especially if you don't have any help. So separating the mirrors from the hinge could make the task less superhuman! Before you separate them, read on... there are reasons why you might not want to!
Since you are dealing with a ridiculously heavy item... glass on particleboard... my first thought is to use the heaviest super duper way I know of to hang anything on a wall. You will attach a wood hanging strip on the back of the mirrors and a mating strip on the wall. These strips will interlock, holding the mirror to the wall securely and making hanging and removal (if necessary) much easier. A second advantage to this method is that leveling the mirror is a piece of cake, since you do all the leveling on the hanging strips. Once the mirror is in place, it will be level unless Mother Nature sucks your home into the earth!
Screw and glue a strip of 1x2" pine, approximately two inches shorter than the distance across the back of each mirror or pairs of mirrors. Predrill the holes in the particle board and the strips for maximum strength. Be sure to use flat head wood screws or drywall screws and be careful with the length. If you drive the screws too deeply or use screws that are too long you will crack the mirror and have to make a trip to the dump! This strip should be located a few inches down from the top, a few inches less in length than the width of the mirror, centered horizontally and perfectly parallel to the top edge. Then, install a similarly sized piece of thin 1/8" plywood over the 1x2, screwed and glued, but have it extend slightly below the 1x2 so that you have a "lip". To make your work a little easier, you can preassemble the hanging strips and then attach them to the mirrors (and the wall, below).
Install an identical 1x2 and plywood strip level on the wall in the position you want it. Note that the overlap forming the two "lips" should be identical on both strips. But for the wall strip, remember to locate the "lip" on the top. Here is the one time where keeping the two mirrors double-width is an advantage. You have a total width of about 32", which should give you at least two of the wall studs to screw into. Using a single width of mirror will only allow you to have one stud behind each mirror, forcing you to use toggle anchors. Toggles will hold the mirror... use a 3/16" toggle for extra strength... but screwing into a firm stud is even better!
Hanging the mirror is easy...the two "lips" will interlock like two kids with braces (smack!!) holding the heavy mirror firmly in place. You might also want to install a 1x2 spacer across the bottom of each mirror to square it up on the wall and also so that the mirror won't pivot or swing on the top support. A really good idea!
The only problem with this method is that it positions the mirror quite a bit from the wall. However, you can use other materials, such as 1/2" plywood strip instead of the 1" pine to slightly reduce the thickness. You could also use a piece of flat iron instead of the plywood "lip" to further reduce the thickness. Of course with the metal you would be better attaching the wood to the mirror first, then the metal strip. Preconstructing would force you to drill through the metal adding to the difficulty of the job.
If you have more woodworking power tools available, a neat option would be to use an electric router or table saw to cut the "lip" right into the pine 1x2, saving the extra assembly and material thickness.
I will also offer a non-carpentry alternative which has its pluses and minuses. Visit your local hardware store and look for a type of hanging ring that would attach to the back of the mirror with screws. This is a metal ring that pivots on a steel strip with multiple screw holes (use a minimum three-holer for this installation), allowing its use for a variety of hanging projects. Predrill the holes for the screws, and use the largest size sheetmetal screw that will easily fit through the holes in the hanging rings. Remember not to get screws that are too long!
You will have to install nails or screws into the wall to hang the rings on. Depending on your walls, you might be able to screw right into the studs (if they are in the right places) or you will have to use molly anchors. Use the 3/16" size and be sure to get a hanging ring that is large enough to go over the top of the molly's screw head.
It will be more difficult to position the hardware properly and to level the mirror using this method, but it can be done with scrupulous measuring and patience. The key is the get the hanging rings in perfect position on the mirrors first, and then transferring this measurement to the wall. A trick... do not install all the screws through the hanging ring strips on your first try. Instead, install only the bottommost screws. Do a test hang. If the mirror is level, take it down and install the rest of the screws. If not, you can reposition one of the hanging rings slightly, using the remaining screw holes. Screwing into particle board weakens it, so you cannot locate two screws less than about 1/4" apart and expect the strongest grip.
I could come up with more variations on this theme, but time and space does not permit. Hope this is helpful.
Have a small home repair question for THE NATURAL HANDYMAN? Just click here www.naturalhandyman.com/aitikia
For more home repair information, visit NH's growing list of original home repair articles and quality links www.naturalhandyman.com
If this information has been valuable to you, please consider making a small donation to support NH's free service to the home repair community! For more information, please visit our "Friends" page www.naturalhandyman.com/friends
The Natural Handyman Site Directory
- Home Repair Articles www.naturalhandyman.com/iip
- Home Repair Links Library www.naturalhandyman.com/linkslibrary
- NH's Bookshop www.naturalhandyman.com/bookshop
- Find a handyman at www.naturalhandyman.com/network
- Win unique home repair gifts and prizes at www.naturalhandyman.com/contest
Please read the important copyright and disclaimer information is located at www.naturalhandyman.com/copyright
Also in Home
- How to build a contemporary outdoor fireplace
- Finding an affordable safe handyman
- Tips for taking in a renter
- How little things can make your décor pop
- Building a winter green house
- A natural approach to eliminating pet odors
- Cost-effective solutions to rid your home of black snakes
- 5 ways your house can make you go broke
- 5 simple and affordable luxuries for your home
- Does staging really raise a home's price?
- 5 home renovation can raise your insurance rate -- or lead to discounts
- The right way and wrong way to pay down your mortgage
- 6 cheap, effective home security solutions
- 3 ways (and 1 reason) to refinance a HELOC
- 6 home projects that don't pay for themselves
- Should I refinance my home equity line?
- Find the best mortgage rates in your area
- 3 ways to use a mortgage calculator
- Mortgage calculator: Calculate your payment and more
- Home equity calculator: HELOC vs. line of credit
- Mortgage refinance break-even calculator
- How much money can I borrow for a mortgage?